Pride Mobility power chairs / scooters screw size
M5 · 30 mm long
Pride Mobility power chairs / scooters takes M5 metric screws, 30 mm long.
The record covers pride Mobility replacement part SCRPPH1315 is an M5-0.8 x 30mm pan-head screw used across Pride power wheelchair and scooter assemblies.
Head and drive, as the source states them: pan head.
This entry is marked confirmed and comes from quickie-wheelchairs.com.
For reference, M5 is 5 mm across the threads at 0.8 mm pitch. The imperial size people confuse it with: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Pride Mobility power chairs / scooters screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | 30 mm | 0.8 mm | Pan head | not stated | Pride Mobility replacement part SCRPPH1315 is an M5-0.8 x 30mm pan-head screw used across Pride power wheelchair and scooter assemblies | Confirmed |
Fitment records and sources
Pride Mobility replacement part SCRPPH1315 is an M5-0.8 x 30mm pan-head screw used across Pride power wheelchair and scooter assemblies.
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- Keep material and finish the same as the original (often stainless) on equipment that is cleaned or sterilised.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for pan head screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The record states 30 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- Wheelchair and mobility OEM screws specify an exact standard and strength class (ISO 7045 CL4.8, ISO 4762 CL12.9). Matching only the thread size can cause a failure under load.
- Espresso shower-screen screws vary in length across brands (10-16mm) even though thread is consistently M5, so cross-brand length compatibility is not guaranteed.
More in Medical & Laboratory
The same screw also fits
Devices whose records share a thread with Pride Mobility power chairs / scooters, closest length match first.
- Flat-pack furniture also M5 × 30 mm
- Atdec Telehook TH-2250-VF display wall mount also M5 × 30 mm
- Drum tension rod also M5 × 30 mm
- Voron 2.4 / Trident also M5 × 30 mm
- Raymarine Axiom 7/9/12 multifunction display also M5 × 30 mm
- Appliance handles also M5 × 30 mm
- Bullet CCTV camera housing also M5 × 30 mm
- Door lever through-bolts also M5 × 30 mm
Questions about Pride Mobility power chairs / scooters screws
- What size screw does Pride Mobility power chairs / scooters use?
- M5 × 30 mm for pride Mobility replacement part SCRPPH1315 is an M5-0.8 x 30mm pan-head screw used across Pride power wheelchair and scooter assemblies.
- How long are the screws in Pride Mobility power chairs / scooters?
- The record gives 30 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Pride Mobility power chairs / scooters?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.