Samsung TV pedestal stand (24-55in) screw size
M4 · 14 mm long
Samsung TV pedestal stand (24-55in) takes M4 metric screws, 14 mm long.
The record covers attaches the stand base to the TV chassis.
This entry is marked reported and comes from electronics.alibaba.com.
M4 means a 4 mm nominal diameter with a 0.7 mm thread pitch. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Samsung TV pedestal stand (24-55in) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 14 mm | 0.7 mm | not stated | not stated | Attaches the stand base to the TV chassis | Reported |
Fitment records and sources
Attaches the stand base to the TV chassis
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 14 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Dashcam mounts advertised as '1/4" M4 screw joint' have two different threads: the 1/4"-20 camera thread and a separate M4 grub screw for the ball joint — don't order the wrong one.
- Most HVAC chassis hardware in US-market units is imperial; metric shows up mainly on European-made components.
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with Samsung TV pedestal stand (24-55in), closest length match first.
- Samsung range / wall oven also M4 × 14 mm
- LED downlight trim and driver also M4 × 14 mm
- Raymarine Alpha Series Display Mast Bracket also M4 × 14 mm
- Telescope knurled locking/tension screw for diagonals, adapters, focusers also M4 × 14 mm
- Washing machine control panel also M4 × 14 mm
- Monitor arms (Ergotron LX and generic) also M4 × 14 mm
- GCX 75/100mm VESA flush display mount also M4 × 14 mm
- Speaker grille and handle hardware also M4 × 14 mm
Questions about Samsung TV pedestal stand (24-55in) screws
- What size screw does Samsung TV pedestal stand (24-55in) use?
- M4 × 14 mm for attaches the stand base to the TV chassis.
- How long are the screws in Samsung TV pedestal stand (24-55in)?
- The record gives 14 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Samsung TV pedestal stand (24-55in)?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.