Sauer 200 STR / SSG3000 Vision chassis screw size
M6 · 20 mm long
Our records put Sauer 200 STR / SSG3000 Vision chassis on M6 screws, 20 mm long.
The record covers hexagon socket head cap screw VDS-0002 for action-to-chassis mounting.
Head and drive, as the source states them: socket cap head.
This entry is marked confirmed and comes from skytterlinken.no.
For reference, M6 is 6 mm across the threads at 1 mm pitch. The imperial size people confuse it with: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Sauer 200 STR / SSG3000 Vision chassis screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 20 mm | 1 mm | Socket cap | not stated | hexagon socket head cap screw VDS-0002 for action-to-chassis mounting | Confirmed |
Fitment records and sources
hexagon socket head cap screw VDS-0002 for action-to-chassis mounting
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Outdoor hardware should be stainless or coated to stop corrosion seizing it in place.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for socket cap screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The record states 20 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- VESA display mounts are M4, M6 or M8 depending on the pattern size; measure before ordering.
- Trailer license plate mounts frequently use 1/4 inch screws in the US, but international and many modern bracket kits have shifted to M6.
More in Sports, Outdoors & Optics Mounts
Accuracy International AT/AX AICS chassisAlpine binding heel/toe piece (heavy duty)Archery/bow accessory set screws (generic component, not confirmed as sight-specific)Bodypoint wheelchair T-slot mounting kitBurton EST bindings on The ChannelBurton Re:Flex snowboard bindings (4x4 / 3D boards)Elliptical pedal arm boltsFishing reel handle and drag knobFishing reel handle screw/nut locking plateFishing reel side platesFuge EVOLVE ski binding mounting jigHeart rate chest strap buckle
Browse all 30 in Sports, Outdoors & Optics Mounts →The same screw also fits
Devices whose records share a thread with Sauer 200 STR / SSG3000 Vision chassis, closest length match first.
- Alpine binding heel/toe piece (heavy duty) also M6 × 20 mm
- Powersports battery terminal bolts also M6 × 20 mm
- Appliance door hinges also M6 × 20 mm
- Pride Go-Go scooter tiller lock knob also M6 × 20 mm
- License plate / number plate mounting (Dorman 784-518 universal fastener) also M6 × 20 mm
- Optical breadboard / optical table (metric) also M6 × 20 mm
- WABCO/ZF OnSide blind spot radar sensor bracket also M6 × 20 mm
- USD inline skate frame mounting bolt also M6 × 20 mm
Questions about Sauer 200 STR / SSG3000 Vision chassis screws
- What size screw does Sauer 200 STR / SSG3000 Vision chassis use?
- M6 × 20 mm for hexagon socket head cap screw VDS-0002 for action-to-chassis mounting.
- How long are the screws in Sauer 200 STR / SSG3000 Vision chassis?
- The record gives 20 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Sauer 200 STR / SSG3000 Vision chassis?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.