Ski-Doo windshield and console assembly screw size
M6 · 20 mm long
If you are replacing a screw on Ski-Doo windshield and console assembly, the thread is M6, 20 mm long.
Where it is used: OEM parts fiche lists Torx truss screw M6 x 20mm.
Head and drive, as the source states them: truss head and Torx drive.
This entry is marked confirmed and comes from engelhart.com.
M6 means a 6 mm nominal diameter with a 1 mm thread pitch. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Ski-Doo windshield and console assembly screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 20 mm | 1 mm | Truss head | Torx | OEM parts fiche lists Torx truss screw M6 x 20mm | Confirmed |
Fitment records and sources
OEM parts fiche lists Torx truss screw M6 x 20mm
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- For a wall or arm mount, the screw has to engage the threaded insert by several turns but must not bottom out, so measure the insert depth and add the thickness of the bracket and any spacers.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for truss head screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The record states 20 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source names a Torx drive. For comparison, standard M6 heads take PH3 (Phillips) or T30 (Torx), or a 5 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- VESA displays over 50kg move up to M8 x 1.25, which is outside metric M6 hardware - don't force an M6 bolt into a heavy-panel mount.
- VESA display mounts are M4, M6 or M8 depending on the pattern size; measure before ordering.
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with Ski-Doo windshield and console assembly, closest length match first.
- VESA MIS-E/F display mount (200mm+) also M6 × 20 mm
- Universal full-motion TV mount kits also M6 × 20 mm
- StarTech Universal Projector Wall Mount (PROJWALLMNT) also M6 × 20 mm
- Signage standoffs also M6 × 20 mm
- Pro-AV truss clamps also M6 × 20 mm
- VESA MIS-F large display mount also M6 × 20 mm
- Atdec Telehook TH-2250-VF display wall mount also M6 × 20 mm
- Speaker flying frame / eyebolt hardware also M6 × 20 mm
Questions about Ski-Doo windshield and console assembly screws
- What size screw does Ski-Doo windshield and console assembly use?
- M6 × 20 mm for OEM parts fiche lists Torx truss screw M6 x 20mm.
- How long are the screws in Ski-Doo windshield and console assembly?
- The record gives 20 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Ski-Doo windshield and console assembly?
- The source lists a Torx drive. Standard M6 heads otherwise take PH3 (Phillips) or T30 (Torx), or a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.