Sony Bravia TV stand (part S0501559001) screw size
M5 · 6 mm long
If you are replacing a screw on Sony Bravia TV stand (part S0501559001), the thread is M5, 6 mm long.
It is listed for genuine Sony Bravia stand screw M5 x 6mm.
This entry is marked likely and comes from speedyspares.com.
M5 means a 5 mm nominal diameter with a 0.8 mm thread pitch. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Sony Bravia TV stand (part S0501559001) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | 6 mm | 0.8 mm | not stated | not stated | Genuine Sony Bravia stand screw M5 x 6mm | Likely |
Fitment records and sources
Genuine Sony Bravia stand screw M5 x 6mm
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- For a wall or arm mount, the screw has to engage the threaded insert by several turns but must not bottom out, so measure the insert depth and add the thickness of the bracket and any spacers.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 6 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- The 'GoPro thread' is M5-0.8, a de facto standard on third-party mounts, and is not the imperial 1/4-20 tripod thread.
- M5x0.8 is the de facto universal bike thread — confirm 0.8mm pitch before threading into carbon or alloy bosses.
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with Sony Bravia TV stand (part S0501559001), closest length match first.
- QualGear QG-KIT-VA-3IN-B Projector Mounting Kit also M5 × 6 mm
- SISAB ECO.50+/T laboratory centrifuge also M5 × 6 mm
- Aftermarket car stereo cage also M5 × 6 mm
- Shimano BL-M785 hydraulic brake lever also M5 × 6 mm
- Marine-grade set/grub screw (DIN 916, A4 stainless) also M5 × 6 mm
- Electrolux Professional compact rack-type dishwasher also M5 × 6 mm
- HIWIN QHH35 / QEH20 linear guideway end-cap/lubrication unit fixing screws also M5 × 6 mm
- Espresso portafilter basket spring also M5 × 6 mm
Questions about Sony Bravia TV stand (part S0501559001) screws
- What size screw does Sony Bravia TV stand (part S0501559001) use?
- M5 × 6 mm for genuine Sony Bravia stand screw M5 x 6mm.
- How long are the screws in Sony Bravia TV stand (part S0501559001)?
- The record gives 6 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Sony Bravia TV stand (part S0501559001)?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.