Stage light yoke brackets screw size
M5 · 12 to 20 mm long
Our records put Stage light yoke brackets on M5 screws in lengths from 12 to 20 mm.
Where it is used: moving head and PAR yoke bracket screws.
This entry is marked reported.
M5 means a 5 mm nominal diameter with a 0.8 mm thread pitch. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Stage light yoke brackets screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | 12–20 mm | 0.8 mm | not stated | not stated | Moving head and PAR yoke bracket screws | Reported |
Fitment records and sources
Moving head and PAR yoke bracket screws
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 12–20 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- Truss and stage-light clamps use M8 or M10 bolts depending on tube diameter — larger than anything in this database, so don't substitute an M6.
- The 'GoPro thread' is M5-0.8, a de facto standard on third-party mounts, and is not the imperial 1/4-20 tripod thread.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M5 x 12mm Black Wafer Head Cut-off Saw Screws for STIHL TS400 Cut-off Saw (replaces IS-M5x12 9022 341 0960) – 10-Pack Replacement
$5.99Choose size -
M5 x 12mm Black Wafer Head Generator Cover Screws for Honda EM, EB, EG Generators & EU3200i (replaces 90102-Z21-000) – 10-Pack Replacement
$5.99Choose size
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with Stage light yoke brackets, closest length match first.
- Panasonic TC-65GX700 also M5 × 12 mm
- LG 55LW5600 also M5 × 14.5 mm
- LG 47LW5700 also M5 × 14.5 mm
- LG 55LK530 also M5 × 14.5 mm
- LG 55LW6500 also M5 × 14.5 mm
- LG 47LV5500 also M5 × 14.5 mm
- LG 60PZ750 also M5 × 14.5 mm
- LG 42LV3700 also M5 × 14.5 mm
Questions about Stage light yoke brackets screws
- What size screw does Stage light yoke brackets use?
- M5 × 12–20 mm for moving head and PAR yoke bracket screws.
- How long are the screws in Stage light yoke brackets?
- The records range from 12 to 20 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Stage light yoke brackets?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.