Panasonic TC-65GX700 screw size
M4 / M5 · 12 mm long
Our records put Panasonic TC-65GX700 on M4 and M5 screws, 12 mm long.
There are 2 separate fitment records for it, including stand (M4) and stand (M5).
2 of the 2 records are marked confirmed, drawn from 1 source (help.na.panasonic.com).
M4 means a 4 mm nominal diameter with a 0.7 mm thread pitch. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Panasonic TC-65GX700 screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 12 mm | 0.7 mm | not stated | not stated | Stand | Confirmed |
| M5 | 12 mm | 0.8 mm | not stated | not stated | Stand | Confirmed |
Fitment records and sources
Stand
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
Stand
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). This device also uses M5, so measure each screw rather than assuming they match.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 12 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4 / M5
- Dashcam mounts advertised as '1/4" M4 screw joint' have two different threads: the 1/4"-20 camera thread and a separate M4 grub screw for the ball joint — don't order the wrong one.
- Display mounts mix systems: the screen side is metric M4/M6, but the wall side of many mounts uses imperial wood screws such as #14 x 2.5in.
- The 'GoPro thread' is M5-0.8, a de facto standard on third-party mounts, and is not the imperial 1/4-20 tripod thread.
- M5x0.8 is the de facto universal bike thread — confirm 0.8mm pitch before threading into carbon or alloy bosses.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M4 x 12mm Black Wafer Head Chainsaw & Cut-off Saw Screws for STIHL MS 460, MS 362, TS480i & TS500i (IS-M4x12) – 10-Pack Replacement
$5.49Choose size -
M4 x 12mm Black Wafer Head Monitor VESA, Neck & Stand Screws for Dell UltraSharp U4320Q & Sceptre Monitors – 8-Pack Replacement
$5.49Choose size -
M5 x 12mm Black Wafer Head Cut-off Saw Screws for STIHL TS400 Cut-off Saw (replaces IS-M5x12 9022 341 0960) – 10-Pack Replacement
$5.99Choose size -
M5 x 12mm Black Wafer Head Generator Cover Screws for Honda EM, EB, EG Generators & EU3200i (replaces 90102-Z21-000) – 10-Pack Replacement
$5.99Choose size
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with Panasonic TC-65GX700, closest length match first.
- LG 55LW5600 also M4 × 12 mm
- Stage light yoke brackets also M5 × 12 mm
- LG 55LK530 also M4 × 12 mm
- LG 55LW6500 also M4 × 12 mm
- LG 47LW5700 also M4 × 12 mm
- LED aluminium channel end caps also M4 × 12 mm
- LG 47LV5500 also M4 × 12 mm
- Samsung range / wall oven also M4 × 12 mm
Questions about Panasonic TC-65GX700 screws
- What size screw does Panasonic TC-65GX700 use?
- M4 × 12 mm for stand; M5 × 12 mm for stand.
- How long are the screws in Panasonic TC-65GX700?
- The record gives 12 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Panasonic TC-65GX700?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.