Stinger SE-SDIN single-DIN mounting kit display bracket screw size
M5 · 10 mm long
Our records put Stinger SE-SDIN single-DIN mounting kit display bracket on M5 screws, 10 mm long.
It is listed for hardware list specifies M5 x 10 screws for the display bracket.
This entry is marked confirmed and comes from manuzoid.com.
An M5 screw is 5 mm in diameter with a 0.8 mm pitch, tapped with a 4.2 mm drill; imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Stinger SE-SDIN single-DIN mounting kit display bracket screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | 10 mm | 0.8 mm | not stated | not stated | Hardware list specifies M5 x 10 screws for the display bracket | Confirmed |
Fitment records and sources
Hardware list specifies M5 x 10 screws for the display bracket
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 10 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- Espresso/coffee-equipment M5 and M6 socket-head screws (DIN 7984/UNI 9327) are cross-brand standard fasteners shared across CMA, Astoria, and La Cimbali brewing-group hardware, so a single screw often services multiple manufacturers' machines.
- Commercial washer-extractor cabinets mix DIN 933 (hex head, full thread) and DIN 84A (slotted pan/cheese head) M5 screws for different panels on the same machine line, so a single family/brand isn't consistent across all fasteners.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M5 x 10mm Black Wafer Head Bike Fender & Rack Screws for Tern MTR Fenders, Blackburn EX-1 Rack, ENVO Stax & René Herse Fender Set – 10-Pack Replacement
$5.99Choose size -
M5 x 10mm Black Wafer Head Folding Mechanism Screws for GOTRAX GXL V2, Rival, XR Ultra & XR Elite – 10-Pack Replacement
$5.99Choose size
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with Stinger SE-SDIN single-DIN mounting kit display bracket, closest length match first.
- Track lighting heads also M5 × 10 mm
- ATV plastics and fenders also M5 × 10 mm
- M VESA Digital Signage Wallmount also M5 × 10 mm
- Bullet CCTV camera housing also M5 × 10 mm
- QualGear QG-KIT-VA-3IN-B Projector Mounting Kit also M5 × 10 mm
- OpenBuilds V-Slot T-nut bolts also M5 × 10 mm
- Bike kickstand plates also M5 × 10 mm
- E-bike controller mounting plate also M5 × 10 mm
Questions about Stinger SE-SDIN single-DIN mounting kit display bracket screws
- What size screw does Stinger SE-SDIN single-DIN mounting kit display bracket use?
- M5 × 10 mm for hardware list specifies M5 x 10 screws for the display bracket.
- How long are the screws in Stinger SE-SDIN single-DIN mounting kit display bracket?
- The record gives 10 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Stinger SE-SDIN single-DIN mounting kit display bracket?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.