Trimble NAV-900 on Case IH / CNH tractors screw size
M6 · length not stated in the sources
If you are replacing a screw on Trimble NAV-900 on Case IH / CNH tractors, the thread is M6. None of the sources we found gives an exact length, so measure the original before you order.
It is listed for CNH factory mounting plate fasteners.
This entry is marked confirmed and comes from Trimble NAV-900 Installation Guide 108993-00-ENG Rev C.
An M6 screw is 6 mm in diameter with a 1 mm pitch, tapped with a 5 mm drill; imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Trimble NAV-900 on Case IH / CNH tractors screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | not stated | 1 mm | not stated | not stated | CNH factory mounting plate fasteners | Confirmed |
Fitment records and sources
CNH factory mounting plate fasteners
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Industrial parts lists usually give the full callout (thread, length, head, grade); match all four, not just the thread.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
More in Industrial & Machinery
The same screw also fits
Devices whose records share a thread with Trimble NAV-900 on Case IH / CNH tractors, closest length match first.
- Juki MF-7900 industrial coverstitch machine also M6
- INOX stainless hexagon head hygienic bolt with seal, for sanitary/food machinery also M6
- Trimble NAV-900 on John Deere tractors also M6
- Makita JR3051TK reciprocating saw also M6
- Husqvarna 327RDX brushcutter housing also M6
- Rhea Vendors Luce Publico vending machine also M6
- Turck BTS-DSU35-ZF05-M6 mounting kit for manual valves/sensor accessories also M6
- ABB ACS580 terminal hardware (frames R3-R5) also M6
Questions about Trimble NAV-900 on Case IH / CNH tractors screws
- What size screw does Trimble NAV-900 on Case IH / CNH tractors use?
- M6 for CNH factory mounting plate fasteners.
- How long are the screws in Trimble NAV-900 on Case IH / CNH tractors?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Trimble NAV-900 on Case IH / CNH tractors?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.