VESA FDMI Part F large-format interface screw size
M6 · 10 to 12 mm long
The screws used on VESA FDMI Part F large-format interface are M6 in lengths from 10 to 12 mm.
The record covers 6mm diameter 1.0 pitch metric bolts into minimum-depth threaded holes.
This entry is marked confirmed and comes from glenwing.github.io.
M6 means a 6 mm nominal diameter with a 1 mm thread pitch. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
VESA FDMI Part F large-format interface screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 10–12 mm | 1 mm | not stated | not stated | 6mm diameter 1.0 pitch metric bolts into minimum-depth threaded holes | Confirmed |
Fitment records and sources
6mm diameter 1.0 pitch metric bolts into minimum-depth threaded holes
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- For a wall or arm mount, the screw has to engage the threaded insert by several turns but must not bottom out, so measure the insert depth and add the thickness of the bracket and any spacers.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 10–12 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- VESA displays over 50kg move up to M8 x 1.25, which is outside metric M6 hardware - don't force an M6 bolt into a heavy-panel mount.
- VESA display mounts are M4, M6 or M8 depending on the pattern size; measure before ordering.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Displays, TVs & Mounts
The same screw also fits
Devices whose records share a thread with VESA FDMI Part F large-format interface, closest length match first.
- Premier Mounts PBL-UMS/PBL-UMW Universal Projector Mount also M6 × 12 mm
- Sony Bravia mid-size TVs also M6 × 10–12 mm
- QualGear QG-KIT-VA-3IN-B Projector Mounting Kit also M6 × 10 mm
- LED video wall cabinet, frame-to-frame (SCREW A) also M6 × 10 mm
- LG TVs 43-55in also M6 × 10–12 mm
- TCL & Vizio 43-55in TVs also M6 × 12 mm
- VESA 200x200 and larger (MIS-E/F) also M6 × 10–12 mm
- StarTech PROJWALLMNT universal projector wall mount also M6 × 10 mm
Questions about VESA FDMI Part F large-format interface screws
- What size screw does VESA FDMI Part F large-format interface use?
- M6 × 10–12 mm for 6mm diameter 1.0 pitch metric bolts into minimum-depth threaded holes.
- How long are the screws in VESA FDMI Part F large-format interface?
- The records range from 10 to 12 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for VESA FDMI Part F large-format interface?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.