Sony Bravia mid-size TVs screw size
M6 · 10 to 14 mm long
Sony Bravia mid-size TVs takes M6 metric screws in lengths from 10 to 14 mm.
Where it is used: VESA 200x200 / 300x300, M6 screws typical.
This entry is marked reported and comes from screenmounts.com.au.
An M6 screw is 6 mm in diameter with a 1 mm pitch, tapped with a 5 mm drill; imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Sony Bravia mid-size TVs screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 10–14 mm | 1 mm | not stated | not stated | VESA 200x200 / 300x300, M6 screws typical | Reported |
Fitment records and sources
VESA 200x200 / 300x300, M6 screws typical
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 10–14 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- VESA display mounts are M4, M6 or M8 depending on the pattern size; measure before ordering.
- VESA displays over 50kg move up to M8 x 1.25, which is outside metric M6 hardware - don't force an M6 bolt into a heavy-panel mount.
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with Sony Bravia mid-size TVs, closest length match first.
- QualGear QG-KIT-VA-3IN-B Projector Mounting Kit also M6 × 10 mm
- Trimble GFX-350 / GFX-750 / XCN-750 / XCN-1050 guidance displays also M6 × 14 mm
- LED video wall cabinet, frame-to-frame (SCREW A) also M6 × 10 mm
- LG TVs 43-55in also M6 × 10–14 mm
- VESA FDMI Part F large-format interface also M6 × 10–12 mm
- Premier Mounts PBL-UMS/PBL-UMW Universal Projector Mount also M6 × 12–14 mm
- StarTech PROJWALLMNT universal projector wall mount also M6 × 10 mm
- TV wall mount, VESA 200x200 and larger also M6 × 12–14 mm
Questions about Sony Bravia mid-size TVs screws
- What size screw does Sony Bravia mid-size TVs use?
- M6 × 10–14 mm for VESA 200x200 / 300x300, M6 screws typical.
- How long are the screws in Sony Bravia mid-size TVs?
- The records range from 10 to 14 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Sony Bravia mid-size TVs?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.