VESA MIS-E displays (23-30.9 inch) screw size
M4 · 10 mm long
VESA MIS-E displays (23-30.9 inch) takes M4 metric screws, 10 mm long.
The record covers VESA FDMI standard: six M4 x 0.7 mounting screws, 10mm.
This entry is marked confirmed and comes from upgradeinnovations.com.
M4 means a 4 mm nominal diameter with a 0.7 mm thread pitch. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
VESA MIS-E displays (23-30.9 inch) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 10 mm | 0.7 mm | not stated | not stated | VESA FDMI standard: six M4 x 0.7 mounting screws, 10mm | Confirmed |
Fitment records and sources
VESA FDMI standard: six M4 x 0.7 mounting screws, 10mm
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 10 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- VESA size follows the hole pattern, not the brand: MIS-D uses M4, MIS-E/F uses M6 or M8.
- TV mount screw size follows the VESA pattern, not the brand — the same maker's small and large sets need M4, M6 or M8.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
More in Displays, TVs & Mounts
The same screw also fits
Devices whose records share a thread with VESA MIS-E displays (23-30.9 inch), closest length match first.
- GCX 75/100mm VESA flush display mount also M4 × 10 mm
- LED video wall cabinet top screw F and side screw D also M4 × 10 mm
- Dell U2419HC also M4 × 10 mm
- Dell P2714H also M4 × 10 mm
- Dell P2815Q also M4 × 10 mm
- Samsung TV pedestal stand (19-22in) also M4 × 10 mm
- Samsung monitors & smaller TVs also M4 × 10 mm
- VESA MIS-E display mount also M4 × 10 mm
Questions about VESA MIS-E displays (23-30.9 inch) screws
- What size screw does VESA MIS-E displays (23-30.9 inch) use?
- M4 × 10 mm for VESA FDMI standard: six M4 x 0.7 mounting screws, 10mm.
- How long are the screws in VESA MIS-E displays (23-30.9 inch)?
- The record gives 10 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for VESA MIS-E displays (23-30.9 inch)?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.