Yamaha Raptor 700 ATV (2006-2026) screw size
M6 · length not stated in the sources
Yamaha Raptor 700 ATV (2006-2026) takes M6 metric screws. None of the sources we found gives an exact length, so measure the original before you order.
Where it is used: OEM Countersunk Screw (Part 90151-06052-00).
Head and drive, as the source states them: flat / countersunk head.
This entry is marked confirmed and comes from mxlocker.com.
For reference, M6 is 6 mm across the threads at 1 mm pitch. The imperial size people confuse it with: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Yamaha Raptor 700 ATV (2006-2026) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | not stated | 1 mm | Flat / countersunk | not stated | OEM Countersunk Screw (Part 90151-06052-00) | Confirmed |
Fitment records and sources
OEM Countersunk Screw (Part 90151-06052-00).
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: the source describes a countersunk (flat) head, and those are measured overall, from the top of the head to the tip.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- TS-Optics Losmandy-style dovetail bars drill through-holes sized to accept either M6 metric screws or 1/4" imperial screws interchangeably in the same countersunk holes.
- VESA displays over 50kg move up to M8 x 1.25, which is outside metric M6 hardware - don't force an M6 bolt into a heavy-panel mount.
More in Displays, TVs & Mounts
The same screw also fits
Devices whose records share a thread with Yamaha Raptor 700 ATV (2006-2026), closest length match first.
- StarTech Universal Projector Wall Mount (PROJWALLMNT) also M6
- Toshiba 32LF221U21 also M6
- ASUS VG27AQ1A also M6
- VESA MIS-F large display mount also M6
- Trailer License Plate Bracket (BGGTMO) also M6
- Signage standoffs also M6
- 27-34in ultrawide monitors also M6
- Pro-AV truss clamps also M6
Questions about Yamaha Raptor 700 ATV (2006-2026) screws
- What size screw does Yamaha Raptor 700 ATV (2006-2026) use?
- M6 for OEM Countersunk Screw (Part 90151-06052-00).
- How long are the screws in Yamaha Raptor 700 ATV (2006-2026)?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Yamaha Raptor 700 ATV (2006-2026)?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.