Bosch Rexroth T-slot nut, groove 10 mm screw size
M6 · length not stated in the sources
Bosch Rexroth T-slot nut, groove 10 mm takes M6 metric screws. None of the sources we found gives an exact length, so measure the original before you order.
It is listed for M6 T-slot connecting component for 10 mm groove profile.
This entry is marked confirmed and comes from za.rs-online.com.
An M6 screw is 6 mm in diameter with a 1 mm pitch, tapped with a 5 mm drill; imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Bosch Rexroth T-slot nut, groove 10 mm screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | not stated | 1 mm | not stated | not stated | M6 T-slot connecting component for 10 mm groove profile | Confirmed |
Fitment records and sources
M6 T-slot connecting component for 10 mm groove profile.
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- If several screws hold the same part, check that they are all the same length before assuming they are.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
More in Other Equipment
The same screw also fits
Devices whose records share a thread with Bosch Rexroth T-slot nut, groove 10 mm, closest length match first.
- USD inline skate frame mounting bolt also M6
- Furniture leveling foot also M6
- Bosch Rexroth T-slot nut, 30 mm strut, groove 8 mm also M6
- Hygienic USIT sanitary cap nut with collar also M6
- INON Light Adapter for GoPro (dive housing accessory) also M6
- Bosch Rexroth swivel-in T-slot nut, slot 8 also M6
- TE SOLISTRAND ring terminal 50719-1 also M6
- Maedler worm gear motor HMD/II gearbox size 045 square output flange also M6
Questions about Bosch Rexroth T-slot nut, groove 10 mm screws
- What size screw does Bosch Rexroth T-slot nut, groove 10 mm use?
- M6 for M6 T-slot connecting component for 10 mm groove profile.
- How long are the screws in Bosch Rexroth T-slot nut, groove 10 mm?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Bosch Rexroth T-slot nut, groove 10 mm?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.