INON Light Adapter for GoPro (dive housing accessory) screw size
M6 · 10 mm long
If you are replacing a screw on INON Light Adapter for GoPro (dive housing accessory), the thread is M6, 10 mm long.
It is listed for package includes M6 x 10mm cap screws and M6 spacers (6mm) to attach the light/arm adapter to GoPro dive housing mounts.
Head and drive, as the source states them: socket cap head.
This entry is marked confirmed and comes from inon.jp.
M6 means a 6 mm nominal diameter with a 1 mm thread pitch. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
INON Light Adapter for GoPro (dive housing accessory) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 10 mm | 1 mm | Socket cap | not stated | Package includes M6 x 10mm cap screws and M6 spacers (6mm) to attach the light/arm adapter to GoPro dive housing mounts | Confirmed |
Fitment records and sources
Package includes M6 x 10mm cap screws and M6 spacers (6mm) to attach the light/arm adapter to GoPro dive housing mounts
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Take one original screw out first and measure it before ordering; the record above tells you the thread, the original screw tells you the exact length and head.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for socket cap screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The record states 10 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- Mic stand threads (5/8-27) and tripod threads (1/4-20, 3/8-16) are imperial, not metric — only accessory clips like Gravity's M6 adapter are genuinely M6.
- VESA display mounts are M4, M6 or M8 depending on the pattern size; measure before ordering.
More in Other Equipment
2020 aluminium extrusion T-nutsAcer Aspire / SwiftAllen-Bradley PowerFlex 520-series mounting adapter plateAllen-Bradley PowerFlex 750-seriesAllen-Bradley PowerFlex 750-series I/O shield terminationAllen-Bradley PowerFlex 755 IP00 control podAmiga 500 rear/front case screws (Retro32 replacement set)Arduino Uno / MegaASUS / MSI / Gigabyte / ASRock motherboardsBackscatter FLIP3.1 underwater filter frame screws (2x)Backscatter FLIP3.1 underwater flip-frame retaining screwBosch Rexroth swivel-in T-slot nut, slot 8
Browse all 125 in Other Equipment →The same screw also fits
Devices whose records share a thread with INON Light Adapter for GoPro (dive housing accessory), closest length match first.
- VESA FDMI Part F large-format interface also M6 × 10 mm
- Optical breadboard / optical table (metric) also M6 × 10 mm
- Motorcycle side panels and tail cowl also M6 × 10 mm
- Sony Bravia mid-size TVs also M6 × 10 mm
- QualGear QG-KIT-VA-3IN-B Projector Mounting Kit also M6 × 10 mm
- LED video wall cabinet, frame-to-frame (SCREW A) also M6 × 10 mm
- LG TVs 43-55in also M6 × 10 mm
- IV pole clamps also M6 × 10 mm
Questions about INON Light Adapter for GoPro (dive housing accessory) screws
- What size screw does INON Light Adapter for GoPro (dive housing accessory) use?
- M6 × 10 mm for package includes M6 x 10mm cap screws and M6 spacers (6mm) to attach the light/arm adapter to GoPro dive housing mounts.
- How long are the screws in INON Light Adapter for GoPro (dive housing accessory)?
- The record gives 10 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for INON Light Adapter for GoPro (dive housing accessory)?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.