Bosch Rexroth T-slot nut, 30 mm strut, groove 8 mm screw size
M6 · length not stated in the sources
If you are replacing a screw on Bosch Rexroth T-slot nut, 30 mm strut, groove 8 mm, the thread is M6. None of the sources we found gives an exact length, so measure the original before you order.
The record covers M6 T-slot nut for 30 mm strut profile with 8 mm groove.
This entry is marked confirmed and comes from int.rsdelivers.com.
M6 means a 6 mm nominal diameter with a 1 mm thread pitch. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Bosch Rexroth T-slot nut, 30 mm strut, groove 8 mm screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | not stated | 1 mm | not stated | not stated | M6 T-slot nut for 30 mm strut profile with 8 mm groove | Confirmed |
Fitment records and sources
M6 T-slot nut for 30 mm strut profile with 8 mm groove.
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Take one original screw out first and measure it before ordering; the record above tells you the thread, the original screw tells you the exact length and head.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
More in Other Equipment
The same screw also fits
Devices whose records share a thread with Bosch Rexroth T-slot nut, 30 mm strut, groove 8 mm, closest length match first.
- INON Light Adapter for GoPro (dive housing accessory) also M6
- Hygienic USIT sanitary cap nut with collar also M6
- USD inline skate frame mounting bolt also M6
- Furniture leveling foot also M6
- Bosch Rexroth T-slot nut, groove 10 mm also M6
- Eaton 93PX UPS/EBM/MBP (15-20 kVA) also M6
- Tecno kart general fasteners also M6
- Flat-pack furniture cam-lock fittings (IKEA-style knock-down) also M6
Questions about Bosch Rexroth T-slot nut, 30 mm strut, groove 8 mm screws
- What size screw does Bosch Rexroth T-slot nut, 30 mm strut, groove 8 mm use?
- M6 for M6 T-slot nut for 30 mm strut profile with 8 mm groove.
- How long are the screws in Bosch Rexroth T-slot nut, 30 mm strut, groove 8 mm?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Bosch Rexroth T-slot nut, 30 mm strut, groove 8 mm?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.