EHEDG hygienic stainless hex head screw with seal washer screw size
M6 · 20 mm long
If you are replacing a screw on EHEDG hygienic stainless hex head screw with seal washer, the thread is M6, 20 mm long.
The record covers M06 x 20 EHEDG INOX with Fluoroprene XP seal.
This entry is marked confirmed and comes from wdscomponents.com.
An M6 screw is 6 mm in diameter with a 1 mm pitch, tapped with a 5 mm drill; imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
EHEDG hygienic stainless hex head screw with seal washer screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 20 mm | 1 mm | not stated | not stated | M06 x 20 EHEDG INOX with Fluoroprene XP seal | Confirmed |
Fitment records and sources
M06 x 20 EHEDG INOX with Fluoroprene XP seal
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Take one original screw out first and measure it before ordering; the record above tells you the thread, the original screw tells you the exact length and head.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 20 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- Hygienic/3-A food-industry M6 screws are a distinct fastener class (with integrated sealing gasket/washer) from standard DIN 912 M6 socket-head screws; substituting a plain DIN 912 M6 screw on food/sanitary equipment breaks the hygienic seal even though the thread is nominally the same size.
More in Other Equipment
2020 aluminium extrusion T-nutsAcer Aspire / SwiftAllen-Bradley PowerFlex 520-series mounting adapter plateAllen-Bradley PowerFlex 750-seriesAllen-Bradley PowerFlex 750-series I/O shield terminationAllen-Bradley PowerFlex 755 IP00 control podAmiga 500 rear/front case screws (Retro32 replacement set)Arduino Uno / MegaASUS / MSI / Gigabyte / ASRock motherboardsBackscatter FLIP3.1 underwater filter frame screws (2x)Backscatter FLIP3.1 underwater flip-frame retaining screwBosch Rexroth swivel-in T-slot nut, slot 8
Browse all 125 in Other Equipment →The same screw also fits
Devices whose records share a thread with EHEDG hygienic stainless hex head screw with seal washer, closest length match first.
- Kern PFB precision balance internal hardware also M6 × 20 mm
- Roces inline skate frame mounting bolt also M6 × 20 mm
- USD inline skate frame mounting bolt also M6 × 20 mm
- Furniture leveling foot also M6 × 20 mm
- 3030/4040 extrusion end tap also M6 × 20 mm
- Beckhoff AMP8x4x distributed servo drive flange mounting also M6 × 20 mm
- Adult e-scooters also M6 × 20 mm
- RF Elements Twin Horn antenna bracket also M6 × 20 mm
Questions about EHEDG hygienic stainless hex head screw with seal washer screws
- What size screw does EHEDG hygienic stainless hex head screw with seal washer use?
- M6 × 20 mm for M06 x 20 EHEDG INOX with Fluoroprene XP seal.
- How long are the screws in EHEDG hygienic stainless hex head screw with seal washer?
- The record gives 20 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for EHEDG hygienic stainless hex head screw with seal washer?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.