Flute key pivot point screw size
M1.2 · length not stated in the sources
Flute key pivot point takes M1.2 metric screws. None of the sources we found gives an exact length, so measure the original before you order.
Where it is used: threaded pivot holding key arms to the posts.
This entry is marked reported and comes from alibaba.com.
An M1.2 screw is 1.2 mm in diameter with a 0.25 mm pitch, tapped with a 0.95 mm drill; imperial look-alike: #0-80 UNF (1.52 mm) is the closest imperial screw, but it is bigger — not a substitute.
Flute key pivot point screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.2 | not stated | 0.25 mm | not stated | not stated | threaded pivot holding key arms to the posts | Reported |
Fitment records and sources
threaded pivot holding key arms to the posts
pitch 0.25 mm · tap 0.95 mm · clearance 1.4 mm · PH000 / JIS 00 / Torx T1–T2
How to check the screw before you buy
- Stage and rack gear mixes metric with #10-32 rack screws, so check before swapping.
- Diameter: across the threads an M1.2 screw measures about 1.2 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.25 mm from one thread crest to the next (40 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M1.2 heads take PH000 / JIS 00 for Phillips and T1–T2 for Torx; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.2 is about 5-8 N·cm into metal threads and 3-5 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.2
- M1.2 and M1.4 look identical in an eyeglass repair kit — the wrong one strips soft acetate or metal hinges.
More in Audio, Music & Stage
The same screw also fits
Devices whose records share a thread with Flute key pivot point, closest length match first.
- Precision instruments (NBK/SAIDA style) also M1.2
- Bien-Air Dental Handpieces also M1.2
- Eyeglass nose pads also M1.2
- Dell Inspiron 13 7390 2-in-1 also M1.2
- MSI Prestige / GF series laptop (MS-15F4) also M1.2
- Dell Inspiron 13 7378 2-in-1 also M1.2
- Dell Latitude 9430 also M1.2
- Lenovo Yoga Slim 7 Ultra 14IPH11 also M1.2
Questions about Flute key pivot point screws
- What size screw does Flute key pivot point use?
- M1.2 for threaded pivot holding key arms to the posts.
- How long are the screws in Flute key pivot point?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M1.2 screw?
- 0.25 mm (coarse), which is the standard pitch for M1.2 machine screws. The tap drill is 0.95 mm and the normal clearance hole is 1.4 mm.
- What screwdriver do I need for Flute key pivot point?
- The sources do not name the drive. For M1.2, Phillips heads normally take PH000 / JIS 00 and Torx heads T1–T2.
- Can I use an imperial screw instead of M1.2?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) is the closest imperial screw, but it is bigger — not a substitute. Use a true M1.2 screw so it does not cross-thread or strip the hole.