JUKI industrial sewing machine needle plate screw (SM2040750TP) screw size
M4 · length not stated in the sources
Our records put JUKI industrial sewing machine needle plate screw (SM2040750TP) on M4 screws. None of the sources we found gives an exact length, so measure the original before you order.
It is listed for UK parts retailer product titled 'Genuine needle plate screw M4 Juki'.
This entry is marked reported and comes from konsew.co.uk.
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
JUKI industrial sewing machine needle plate screw (SM2040750TP) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | not stated | 0.7 mm | not stated | not stated | UK parts retailer product titled 'Genuine needle plate screw M4 Juki' | Reported |
Fitment records and sources
UK parts retailer product titled 'Genuine needle plate screw M4 Juki'
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Water heater elements use pipe threads (NPSM/NPT), not metric machine screws.
- Dashcam mounts advertised as '1/4" M4 screw joint' have two different threads: the 1/4"-20 camera thread and a separate M4 grub screw for the ball joint — don't order the wrong one.
More in Displays, TVs & Mounts
The same screw also fits
Devices whose records share a thread with JUKI industrial sewing machine needle plate screw (SM2040750TP), closest length match first.
- Samsung TV pedestal stand (24-55in) also M4
- Samsung range / wall oven also M4
- Dell P1917S also M4
- LG 43LJ5000 also M4
- Dell U2417HJ also M4
- LG 60PZ750 also M4
- Thorlabs LDM21/M TE-cooled laser diode mount also M4
- Sanus VHWTV-C universal TV mounting hardware pack also M4
Questions about JUKI industrial sewing machine needle plate screw (SM2040750TP) screws
- What size screw does JUKI industrial sewing machine needle plate screw (SM2040750TP) use?
- M4 for UK parts retailer product titled 'Genuine needle plate screw M4 Juki'.
- How long are the screws in JUKI industrial sewing machine needle plate screw (SM2040750TP)?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for JUKI industrial sewing machine needle plate screw (SM2040750TP)?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.