Philips IntelliVue display mounting bracket screw size
M4 · 8 mm long
The screws used on Philips IntelliVue display mounting bracket are M4, 8 mm long.
Where it is used: four screws attaching VESA-style bracket to display.
This entry is marked confirmed and comes from frankshospitalworkshop.com.
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Philips IntelliVue display mounting bracket screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 8 mm | 0.7 mm | not stated | not stated | four screws attaching VESA-style bracket to display | Confirmed |
Fitment records and sources
four screws attaching VESA-style bracket to display
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- For a wall or arm mount, the screw has to engage the threaded insert by several turns but must not bottom out, so measure the insert depth and add the thickness of the bracket and any spacers.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 8 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Display mounts mix systems: the screen side is metric M4/M6, but the wall side of many mounts uses imperial wood screws such as #14 x 2.5in.
- TV mount screw size follows the VESA pattern, not the brand — the same maker's small and large sets need M4, M6 or M8.
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with Philips IntelliVue display mounting bracket, closest length match first.
- ASUS VG32AQA1A also M4 × 8 mm
- Dell Pro 24 Plus QHD monitor (P2425D) also M4 × 8 mm
- LG 32LM6400 also M4 × 8 mm
- LG 47LM6700 also M4 × 8 mm
- VESA FDMI MIS-D 75/100 display mount also M4 × 8 mm
- Dell Pro 24 Plus monitor (P2425DE) also M4 × 8 mm
- LG 47LM7600 also M4 × 8 mm
- Dell S2425H monitor also M4 × 8 mm
Questions about Philips IntelliVue display mounting bracket screws
- What size screw does Philips IntelliVue display mounting bracket use?
- M4 × 8 mm for four screws attaching VESA-style bracket to display.
- How long are the screws in Philips IntelliVue display mounting bracket?
- The record gives 8 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Philips IntelliVue display mounting bracket?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.