Ritter Implants angled prosthetic screw screw size
M1.6 · length not stated in the sources
Our records put Ritter Implants angled prosthetic screw on M1.6 screws. None of the sources we found gives an exact length, so measure the original before you order.
Where it is used: listed as an M1.6 abutment-level fixation screw.
This entry is marked confirmed and comes from ritterimplants.com.
An M1.6 screw is 1.6 mm in diameter with a 0.35 mm pitch, tapped with a 1.25 mm drill; imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent.
Ritter Implants angled prosthetic screw screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.6 | not stated | 0.35 mm | not stated | not stated | Listed as an M1.6 abutment-level fixation screw | Confirmed |
Fitment records and sources
Listed as an M1.6 abutment-level fixation screw
pitch 0.35 mm · tap 1.25 mm · clearance 1.8 mm · PH00 / Torx T4–T5
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M1.6 screw measures about 1.6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.35 mm from one thread crest to the next (28.57 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M1.6 heads take PH00 for Phillips and T4–T5 for Torx, and a 1.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.6 is about 12-20 N·cm into metal threads and 6-10 N·cm into plastic bosses; snug it up and stop.
More in Displays, TVs & Mounts
The same screw also fits
Devices whose records share a thread with Ritter Implants angled prosthetic screw, closest length match first.
- Dell Pro 14 Plus portable monitor (P1425) also M1.6
- Straumann Axiom TL Plural Dental Implant also M1.6
- HP Chromebook x360 14 inch also M1.6
- Dell Latitude 3380 also M1.6
- Lenovo YOGA 330L-11IGM also M1.6
- Dell Inspiron 14 5441 also M1.6
- Dell Inspiron 14 5440 also M1.6
- Dell XPS 17 9720 also M1.6
Questions about Ritter Implants angled prosthetic screw screws
- What size screw does Ritter Implants angled prosthetic screw use?
- M1.6 for listed as an M1.6 abutment-level fixation screw.
- How long are the screws in Ritter Implants angled prosthetic screw?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M1.6 screw?
- 0.35 mm (coarse), which is the standard pitch for M1.6 machine screws; a 0.2 mm fine pitch exists but is uncommon. The tap drill is 1.25 mm and the normal clearance hole is 1.8 mm.
- What screwdriver do I need for Ritter Implants angled prosthetic screw?
- The sources do not name the drive. For M1.6, Phillips heads normally take PH00 and Torx heads T4–T5; socket heads take a 1.5 mm hex key.
- Can I use an imperial screw instead of M1.6?
- No. Imperial look-alike: #1-72 UNF (1.85 mm) is larger; there is no true imperial equivalent. Use a true M1.6 screw so it does not cross-thread or strip the hole.