Robe MiniMe fixture adjusting screw screw size
M4 · 5 mm long
If you are replacing a screw on Robe MiniMe fixture adjusting screw, the thread is M4, 5 mm long.
It is listed for hexagon socket adjusting screw M4 x 5mm.
This entry is marked likely and comes from lightparts.com.
M4 means a 4 mm nominal diameter with a 0.7 mm thread pitch. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
Robe MiniMe fixture adjusting screw screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 5 mm | 0.7 mm | not stated | not stated | Hexagon socket adjusting screw M4 x 5mm | Likely |
Fitment records and sources
Hexagon socket adjusting screw M4 x 5mm
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Instrument and audio hardware often threads into wood or thin metal; a screw that is too long can poke through a finished surface.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 5 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- M4 and 6-32 UNC share a nominal diameter with different pitch — a classic cross-thread in US-market kits.
More in Audio, Music & Stage
Accordion reed blocksAllparts metric bridge length screwsARRI Mini Follow Focus MFF-2 / related follow-focus hardwareBoss compact guitar pedal battery doorCymbal stand / hi-hat wing nutCymbal stand top wing nutCymbal stand wing nutDrum hardware wing bolt / memory lockDrum tension rodDrum tension rod / lug mounting screwDuratruss Mini 360 F14 10kg truss clampFender Standard Series bass bridge
Browse all 48 in Audio, Music & Stage →The same screw also fits
Devices whose records share a thread with Robe MiniMe fixture adjusting screw, closest length match first.
- Martin MAC 500 moving head fixture also M4 × 5 mm
- Diebold Opteva ATM cassette screw also M4 × 5 mm
- NCR S2 dispenser module screw also M4 × 5 mm
- Meccano boxed sets (modern metric era) and compatible parts also M4 × 5 mm
- Diebold Nixdorf DN100 nylon screw also M4 × 5 mm
- Datalogic DS2400 fixed-mount barcode reader also M4 × 5 mm
- Elo EMV bracket pan-head screw (Bag P) also M4 × 5 mm
- PC case thumbscrews also M4 × 5 mm
Questions about Robe MiniMe fixture adjusting screw screws
- What size screw does Robe MiniMe fixture adjusting screw use?
- M4 × 5 mm for hexagon socket adjusting screw M4 x 5mm.
- How long are the screws in Robe MiniMe fixture adjusting screw?
- The record gives 5 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for Robe MiniMe fixture adjusting screw?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.