Ski binding mounting screws (Binding Freedom) screw size
M5 · 9.5 to 12 mm long
Our records put Ski binding mounting screws (Binding Freedom) on M5 screws in lengths from 9.5 to 12 mm.
The record covers pozi flat head M5 insert screws with 9.5mm head — the aftermarket standard.
Head and drive, as the source states them: flat / countersunk head and Pozidriv drive.
This entry is marked confirmed and comes from bindingfreedom.com.
An M5 screw is 5 mm in diameter with a 0.8 mm pitch, tapped with a 4.2 mm drill; imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Ski binding mounting screws (Binding Freedom) screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | 9.5–12 mm | 0.8 mm | Flat / countersunk | Pozidriv | Pozi flat head M5 insert screws with 9.5mm head — the aftermarket standard | Confirmed |
Fitment records and sources
Pozi flat head M5 insert screws with 9.5mm head — the aftermarket standard
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- Outdoor hardware should be stainless or coated to stop corrosion seizing it in place.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: the source describes a countersunk (flat) head, and those are measured overall, from the top of the head to the tip.
- The records span 9.5–12 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source names a Pozidriv drive. For comparison, standard M5 heads take PH2 (Phillips) or T25 (Torx), or a 4 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- Ski and snowboard binding screws vary by brand and insert system (4x4, Channel, Tyrolia, Marker). Aftermarket suppliers standardise on M5/M6 but OEM screws can be a different pitch.
- This is a third-party/aftermarket metal component, not an official LEGO or LEGO Technic part; standard LEGO Technic axles are unthreaded plastic friction-fit rods.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M5 x 12mm Black Wafer Head Cut-off Saw Screws for STIHL TS400 Cut-off Saw (replaces IS-M5x12 9022 341 0960) – 10-Pack Replacement
$5.99Choose size -
M5 x 12mm Black Wafer Head Generator Cover Screws for Honda EM, EB, EG Generators & EU3200i (replaces 90102-Z21-000) – 10-Pack Replacement
$5.99Choose size -
M5 x 10mm Black Wafer Head Bike Fender & Rack Screws for Tern MTR Fenders, Blackburn EX-1 Rack, ENVO Stax & René Herse Fender Set – 10-Pack Replacement
$5.99Choose size -
M5 x 10mm Black Wafer Head Folding Mechanism Screws for GOTRAX GXL V2, Rival, XR Ultra & XR Elite – 10-Pack Replacement
$5.99Choose size
More in Sports, Outdoors & Optics Mounts
Accuracy International AT/AX AICS chassisAlpine binding heel/toe piece (heavy duty)Archery/bow accessory set screws (generic component, not confirmed as sight-specific)Bodypoint wheelchair T-slot mounting kitBurton EST bindings on The ChannelBurton Re:Flex snowboard bindings (4x4 / 3D boards)Elliptical pedal arm boltsFishing reel handle and drag knobFishing reel handle screw/nut locking plateFishing reel side platesFuge EVOLVE ski binding mounting jigHeart rate chest strap buckle
Browse all 30 in Sports, Outdoors & Optics Mounts →The same screw also fits
Devices whose records share a thread with Ski binding mounting screws (Binding Freedom), closest length match first.
- Wakeboard / water-ski binding plates also M5 × 12 mm
- Snowboard binding disc screws also M5 × 10–12 mm
- Ski binding insert flat-head screw kit also M5 × 9.5–12 mm
- SISAB ECO.50+/T laboratory centrifuge also M5 × 9.5–10 mm
- Track lighting heads also M5 × 10–12 mm
- HP Pavilion 4400 also M5 × 10 mm
- HP Pavilion ze5600 also M5 × 10 mm
- Astoria/CMA espresso solenoid group head (used in coffee kiosk equipment) also M5 × 10 mm
Questions about Ski binding mounting screws (Binding Freedom) screws
- What size screw does Ski binding mounting screws (Binding Freedom) use?
- M5 × 9.5–12 mm for pozi flat head M5 insert screws with 9.5mm head — the aftermarket standard.
- How long are the screws in Ski binding mounting screws (Binding Freedom)?
- The records range from 9.5 to 12 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Ski binding mounting screws (Binding Freedom)?
- The source lists a Pozidriv drive. Standard M5 heads otherwise take PH2 (Phillips) or T25 (Torx), or a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.