Snowboard binding disc screws screw size
M5 · 10 to 16 mm long
If you are replacing a screw on Snowboard binding disc screws, the thread is M5 in lengths from 10 to 16 mm.
Where it is used: binding mounting discs use M5 or M6 depending on the insert system.
Head and drive, as the source states them: binding head.
This entry is marked reported and comes from bindingfreedom.com.
An M5 screw is 5 mm in diameter with a 0.8 mm pitch, tapped with a 4.2 mm drill; imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Snowboard binding disc screws screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | 10–16 mm | 0.8 mm | Binding head | not stated | Binding mounting discs use M5 or M6 depending on the insert system | Reported |
Fitment records and sources
Binding mounting discs use M5 or M6 depending on the insert system
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- Scope and accessory mounts often publish a torque value; tighten to it in a cross pattern.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for binding head screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The records span 10–16 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- Ski and snowboard binding screws vary by brand and insert system (4x4, Channel, Tyrolia, Marker). Aftermarket suppliers standardise on M5/M6 but OEM screws can be a different pitch.
- 2020 extrusion end-tap holes vary between 4.2mm (M5) and 5mm (M6) core depending on manufacturer — always measure before tapping.
More in Sports, Outdoors & Optics Mounts
Accuracy International AT/AX AICS chassisAlpine binding heel/toe piece (heavy duty)Archery/bow accessory set screws (generic component, not confirmed as sight-specific)Bodypoint wheelchair T-slot mounting kitBurton EST bindings on The ChannelBurton Re:Flex snowboard bindings (4x4 / 3D boards)Elliptical pedal arm boltsFishing reel handle and drag knobFishing reel handle screw/nut locking plateFishing reel side platesFuge EVOLVE ski binding mounting jigHeart rate chest strap buckle
Browse all 30 in Sports, Outdoors & Optics Mounts →The same screw also fits
Devices whose records share a thread with Snowboard binding disc screws, closest length match first.
- Pride Mobility wheelchair battery box also M5 × 16 mm
- Wheelchair rear wheel axle bolts also M5 × 15–16 mm
- Ski binding insert flat-head screw kit also M5 × 10–16 mm
- Ski binding mounting screws (Binding Freedom) also M5 × 10–12 mm
- Powersports battery terminal bolts (alt size) also M5 × 15–16 mm
- Elliptical pedal arm bolts also M5 × 15–16 mm
- Wakeboard / water-ski binding plates also M5 × 12–16 mm
- Sea-Doo personal watercraft socket head screw also M5 × 16 mm
Questions about Snowboard binding disc screws screws
- What size screw does Snowboard binding disc screws use?
- M5 × 10–16 mm for binding mounting discs use M5 or M6 depending on the insert system.
- How long are the screws in Snowboard binding disc screws?
- The records range from 10 to 16 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Snowboard binding disc screws?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.