Ski-Doo console hardware nut screw size
M5 · length not stated in the sources
If you are replacing a screw on Ski-Doo console hardware nut, the thread is M5. None of the sources we found gives an exact length, so measure the original before you order.
The record covers OEM parts fiche lists hex flange elastic nut M5 for console and windshield hardware.
This entry is marked confirmed and comes from engelhart.com.
For reference, M5 is 5 mm across the threads at 0.8 mm pitch. The imperial size people confuse it with: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Ski-Doo console hardware nut screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | not stated | 0.8 mm | not stated | not stated | OEM parts fiche lists hex flange elastic nut M5 for console and windshield hardwarewasher / flange face | Confirmed |
Fitment records and sources
OEM parts fiche lists hex flange elastic nut M5 for console and windshield hardware
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- For a wall or arm mount, the screw has to engage the threaded insert by several turns but must not bottom out, so measure the insert depth and add the thickness of the bracket and any spacers.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- Concept2 rowers/ergs look metric-friendly but use imperial 1/4-20 hardware throughout — M6 will NOT thread in; do not force it.
- The 'GoPro thread' is M5-0.8, a de facto standard on third-party mounts, and is not the imperial 1/4-20 tripod thread.
More in Displays, TVs & Mounts
The same screw also fits
Devices whose records share a thread with Ski-Doo console hardware nut, closest length match first.
- LG 47LW5700 also M5
- LG 55LK530 also M5
- LG 55LW6500 also M5
- Stage light yoke brackets also M5
- Panasonic TC-65GX700 also M5
- LG 55LW5600 also M5
- StarTech PROJWALLMNT universal projector wall mount also M5
- Bullet security camera base mounting also M5
Questions about Ski-Doo console hardware nut screws
- What size screw does Ski-Doo console hardware nut use?
- M5 for OEM parts fiche lists hex flange elastic nut M5 for console and windshield hardware.
- How long are the screws in Ski-Doo console hardware nut?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Ski-Doo console hardware nut?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.