Tecno kart general fasteners screw size
M5 / M6 · length not stated in the sources
If you are replacing a screw on Tecno kart general fasteners, the thread is M5 and M6. None of the sources we found gives an exact length, so measure the original before you order.
There are 2 separate fitment records for it, including manual torque table: M5 bolts 3-5 Nm across the kart (M5) and manual torque table: M6 bolts 6-12 Nm across the kart (M6).
2 of the 2 records are marked confirmed, drawn from 1 source (tecnokart.com).
M5 means a 5 mm nominal diameter with a 0.8 mm thread pitch. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Tecno kart general fasteners screw specifications
One row per fitment record. Head, drive and torque are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Torque | Where it goes | Status |
|---|---|---|---|---|---|---|---|
| M5 | not stated | 0.8 mm | not stated | not stated | 3-5 Nm | Manual torque table: M5 bolts 3-5 Nm across the kart | Confirmed |
| M6 | not stated | 1 mm | not stated | not stated | 6-12 Nm | Manual torque table: M6 bolts 6-12 Nm across the kart | Confirmed |
Fitment records and sources
Manual torque table: M5 bolts 3-5 Nm across the kart
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
Manual torque table: M6 bolts 6-12 Nm across the kart
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- Take one original screw out first and measure it before ordering; the record above tells you the thread, the original screw tells you the exact length and head.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). This device also uses M6, so measure each screw rather than assuming they match.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Common mix-ups with M5 / M6
- Espresso/coffee-equipment M5 and M6 socket-head screws (DIN 7984/UNI 9327) are cross-brand standard fasteners shared across CMA, Astoria, and La Cimbali brewing-group hardware, so a single screw often services multiple manufacturers' machines.
- Stacking frame + rack tab + fender stay needs 18-20mm bolts, not the 12-16mm that come with a cage.
- Small wind turbine literature frequently quotes torque or Allen-key size without a thread size; only callouts with an explicit 'M' designation were kept.
- Manual explicitly warns that under-tightening this M6 hinge screw can let the door glass crash into the drum, so torque compliance matters more than just thread match.
More in Other Equipment
The same screw also fits
Devices whose records share a thread with Tecno kart general fasteners, closest length match first.
- Eaton 93PX UPS/EBM/MBP (15-20 kVA) also M5
- Flat-pack furniture cam-lock fittings (IKEA-style knock-down) also M6
- Really Right Stuff B2-Pro-II Arca-Swiss clamp also M6
- Bosch Rexroth T-head bolt, slot 8 also M6
- Maedler worm gear motor HMD/II gearbox size 045 square output flange also M6
- TE SOLISTRAND ring terminal 50719-1 also M6
- Bosch Rexroth swivel-in T-slot nut, slot 8 also M5
- INON Light Adapter for GoPro (dive housing accessory) also M6
Questions about Tecno kart general fasteners screws
- What size screw does Tecno kart general fasteners use?
- M5 for manual torque table: M5 bolts 3-5 Nm across the kart; M6 for manual torque table: M6 bolts 6-12 Nm across the kart.
- How long are the screws in Tecno kart general fasteners?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Tecno kart general fasteners?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.
- How tight should the M5 screw on Tecno kart general fasteners be?
- The source gives 3-5 Nm for manual torque table: M5 bolts 3-5 Nm across the kart.