Treadmill console mounts screw size
M5 · 15 to 30 mm long
If you are replacing a screw on Treadmill console mounts, the thread is M5 in lengths from 15 to 30 mm.
It is listed for console and handlebar mounting bolts.
This entry is marked reported and comes from ifixit.com.
M5 means a 5 mm nominal diameter with a 0.8 mm thread pitch. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing.
Treadmill console mounts screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M5 | 15–30 mm | 0.8 mm | not stated | not stated | Console and handlebar mounting bolts | Reported |
Fitment records and sources
Console and handlebar mounting bolts
pitch 0.8 mm · tap 4.2 mm · clearance 5.5 mm · PH2 / Torx T25
How to check the screw before you buy
- Consoles and controllers often use security drives (tri-wing, Torx) and short screws into plastic bosses, so do not over-tighten.
- Diameter: across the threads an M5 screw measures about 5 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.8 mm from one thread crest to the next (12.5 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The records span 15–30 mm, which means different positions take different lengths — match each hole to its own screw.
- Driver: the source does not name the drive. Standard M5 heads take PH2 for Phillips and T25 for Torx, and a 4 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M5 is about 4.0-6.0 N·m into metal threads and 1.5-2.5 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M5
- Stacking frame + rack tab + fender stay needs 18-20mm bolts, not the 12-16mm that come with a cage.
- The 'GoPro thread' is M5-0.8, a de facto standard on third-party mounts, and is not the imperial 1/4-20 tripod thread.
More in Gaming & Peripherals
Arcade cabinet control panelDell Latitude 3190 / 3190 2-in-1Dell Latitude 3490Dell XPS 13 9315Diebold Nixdorf ATM ESC (Encrypting PIN Pad/keyboard) cross screwDocking station internal boardsFeurich Olya EVO digital piano/E-PianoGeneric tray-mount mechanical keyboardsHTC Vive controllerInkjet printer / scanner framesKBDfans countersunk standoff kitKeychron K3 / K3 Pro / K3 Max
Browse all 30 in Gaming & Peripherals →The same screw also fits
Devices whose records share a thread with Treadmill console mounts, closest length match first.
- Panasonic TC-L42E60 also M5 × 15 mm
- Ski binding insert flat-head screw kit also M5 × 15–26 mm
- QSC K8 loudspeaker yoke bracket also M5 × 16 mm
- Unimac commercial washer (Alliance Laundry Systems OEM part) also M5 × 16 mm
- Bicycle bottle cage bosses (near universal) also M5 × 15–18 mm
- Large / industrial drones also M5 × 15–16 mm
- Juki MF-7900 industrial coverstitch machine also M5 × 16 mm
- GoPro HERO mount thumbscrew also M5 × 18–20 mm
Questions about Treadmill console mounts screws
- What size screw does Treadmill console mounts use?
- M5 × 15–30 mm for console and handlebar mounting bolts.
- How long are the screws in Treadmill console mounts?
- The records range from 15 to 30 mm depending on the position, so match each screw to its own hole.
- What is the thread pitch of an M5 screw?
- 0.8 mm (coarse), which is the standard pitch for M5 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 4.2 mm and the normal clearance hole is 5.5 mm.
- What screwdriver do I need for Treadmill console mounts?
- The sources do not name the drive. For M5, Phillips heads normally take PH2 and Torx heads T25; socket heads take a 4 mm hex key.
- Can I use an imperial screw instead of M5?
- No. Imperial look-alike: #10-32 (4.83 mm) — the other common rack thread; check before mixing. Use a true M5 screw so it does not cross-thread or strip the hole.