Trimble GFX-350 / GFX-750 / XCN-750 / XCN-1050 guidance displays screw size
M6 · 14 mm long
Trimble GFX-350 / GFX-750 / XCN-750 / XCN-1050 guidance displays takes M6 metric screws, 14 mm long.
Where it is used: base plate, roof tray and John Deere adapter mounting.
This entry is marked confirmed and comes from Trimble GFX/XCN Display Series Installation Guide v1.00 Rev .
M6 means a 6 mm nominal diameter with a 1 mm thread pitch. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Trimble GFX-350 / GFX-750 / XCN-750 / XCN-1050 guidance displays screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | 14 mm | 1 mm | not stated | not stated | base plate, roof tray and John Deere adapter mounting | Confirmed |
Fitment records and sources
base plate, roof tray and John Deere adapter mounting
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
Source: Trimble GFX/XCN Display Series Installation Guide v1.00 Rev A
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 14 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- UR cobot flange bolts are commonly sold/quoted as 'M6 bolts' but the required length depends on the tool thickness; UR's own guidance is bolt class M6-8.8 to ISO4762 without a fixed length, so length must be selected per adapter/tool stack-up, not assumed as a fixed mm value.
- VESA display mounts are M4, M6 or M8 depending on the pattern size; measure before ordering.
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with Trimble GFX-350 / GFX-750 / XCN-750 / XCN-1050 guidance displays, closest length match first.
- LG TVs 43-55in also M6 × 14 mm
- Sony Bravia mid-size TVs also M6 × 14 mm
- Premier Mounts PBL-UMS/PBL-UMW Universal Projector Mount also M6 × 14 mm
- TV wall mount, VESA 200x200 and larger also M6 × 14 mm
- VESA 200x200 and larger (MIS-E/F) also M6 × 14 mm
- TCL & Vizio 43-55in TVs also M6 × 14 mm
- VESA MIS-E/F display mount (200mm+) also M6 × 14 mm
- Universal full-motion TV mount kits also M6 × 14 mm
Questions about Trimble GFX-350 / GFX-750 / XCN-750 / XCN-1050 guidance displays screws
- What size screw does Trimble GFX-350 / GFX-750 / XCN-750 / XCN-1050 guidance displays use?
- M6 × 14 mm for base plate, roof tray and John Deere adapter mounting.
- How long are the screws in Trimble GFX-350 / GFX-750 / XCN-750 / XCN-1050 guidance displays?
- The record gives 14 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Trimble GFX-350 / GFX-750 / XCN-750 / XCN-1050 guidance displays?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.