uxcell speaker/amplifier binding post screw size
M4 · 32 mm long
Our records put uxcell speaker/amplifier binding post on M4 screws, 32 mm long.
It is listed for binding post terminal stud, 32mm body.
Head and drive, as the source states them: binding head.
This entry is marked confirmed and comes from amazon.com.
An M4 screw is 4 mm in diameter with a 0.7 mm pitch, tapped with a 3.3 mm drill; imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same.
uxcell speaker/amplifier binding post screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M4 | 32 mm | 0.7 mm | Binding head | not stated | binding post terminal stud, 32mm body | Confirmed |
Fitment records and sources
binding post terminal stud, 32mm body
pitch 0.7 mm · tap 3.3 mm · clearance 4.5 mm · PH2 / Torx T20
How to check the screw before you buy
- Stage and rack gear mixes metric with #10-32 rack screws, so check before swapping.
- Diameter: across the threads an M4 screw measures about 4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.7 mm from one thread crest to the next (14.29 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for binding head screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The record states 32 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M4 heads take PH2 for Phillips and T20 for Torx, and a 3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M4 is about 2.0-3.0 N·m into metal threads and 0.8-1.4 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M4
- Grounding/earth-stud screws on hazardous-area (ATEX/IECEx) gas detectors are commonly M4 even though the enclosure body uses larger threaded glands — don't extrapolate the earth screw size to the whole unit.
- M4 and 6-32 UNC share a nominal diameter with different pitch — a classic cross-thread in US-market kits.
More in Audio, Music & Stage
Accordion reed blocksAllparts metric bridge length screwsARRI Mini Follow Focus MFF-2 / related follow-focus hardwareBoss compact guitar pedal battery doorCymbal stand / hi-hat wing nutCymbal stand top wing nutCymbal stand wing nutDrum hardware wing bolt / memory lockDrum tension rodDrum tension rod / lug mounting screwDuratruss Mini 360 F14 10kg truss clampFender Standard Series bass bridge
Browse all 48 in Audio, Music & Stage →The same screw also fits
Devices whose records share a thread with uxcell speaker/amplifier binding post, closest length match first.
- Kolm Engines EZ77V4 model aircraft engine also M4 × 32 mm
- Heated bed leveling screws also M4 × 32 mm
- cab Applicator A3200 print-and-apply labeling system (packaging line hardware) also M4 × 32 mm
- DIN 912 socket-head cap screw also M4 × 32 mm
- DIN 965 / ISO 7046 countersunk Phillips screw also M4 × 32 mm
- Wurth Elektronik WA-SSTIE steel spacer stud also M4 × 32 mm
- Makita 6095D cordless driver drill also M4 × 32 mm
- Flat-pack cam lock bolt also M4 × 32 mm
Questions about uxcell speaker/amplifier binding post screws
- What size screw does uxcell speaker/amplifier binding post use?
- M4 × 32 mm for binding post terminal stud, 32mm body.
- How long are the screws in uxcell speaker/amplifier binding post?
- The record gives 32 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M4 screw?
- 0.7 mm (coarse), which is the standard pitch for M4 machine screws; a 0.5 mm fine pitch exists but is uncommon. The tap drill is 3.3 mm and the normal clearance hole is 4.5 mm.
- What screwdriver do I need for uxcell speaker/amplifier binding post?
- The sources do not name the drive. For M4, Phillips heads normally take PH2 and Torx heads T20; socket heads take a 3 mm hex key.
- Can I use an imperial screw instead of M4?
- No. Imperial look-alike: #8-32 (4.17 mm) — the standard US PC/rack screw, close but not the same. Use a true M4 screw so it does not cross-thread or strip the hole.