WREKD micro-whoop motors screw size
M1.4 · 3.5 mm long
The screws used on WREKD micro-whoop motors are M1.4, 3.5 mm long.
The record covers RENY / Phillips motor mounting screws.
Head and drive, as the source states them: Phillips drive.
This entry is marked confirmed and comes from wrekd.com.
For reference, M1.4 is 1.4 mm across the threads at 0.3 mm pitch. The imperial size people confuse it with: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
WREKD micro-whoop motors screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | 3.5 mm | 0.3 mm | not stated | Phillips | RENY / Phillips motor mounting screws | Confirmed |
Fitment records and sources
RENY / Phillips motor mounting screws
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- Take one original screw out first and measure it before ordering; the record above tells you the thread, the original screw tells you the exact length and head.
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- The record states 3.5 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source names a Phillips drive. For comparison, standard M1.4 heads take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- Whoop drone M1.4 comes in steel, PEEK and RENY versions: plastic ones are for cameras, not structural frame use.
- Whoop motor screws differ between M1.4x3mm and M1.6x4mm across BetaFPV/NewBeeDrone product generations — check the exact model.
Buy these screws at TechSpare Warehouse
In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.
-
M1.4 Phillips Flat Head Carbon Steel Machine Screws (Multiple Lengths & Finishes)
$5.00Choose size -
M1.4 x 3mm Black Wafer Head Battery Lock Screws for Sennheiser MKH800, SK6000 & SK5012 – 20-Pack Replacement
$4.99Choose size -
M1.6 Phillips Flat Head Carbon Steel Machine Screws (Multiple Lengths & Finishes)
$0.05Choose size -
M1.6 Phillips Flat Head Carbon Steel Machine Screws (Multiple Lengths & Finishes) | 50-Pack
From $4.99Choose size
-
M1.4 x 3.5mm Black Wafer Head Headphone Housing Screws for Sennheiser MOMENTUM On-Ear, M2 OEBT, OEG & OEi – 20-Pack Replacement
$4.99Choose size -
M1.4 x 3.5mm Black Wafer Head Internal Screws for Samsung Galaxy S21, S20, A54, A53, Note 10 – 20-Pack Replacement
$4.99Choose size
More in Other Equipment
2020 aluminium extrusion T-nutsAcer Aspire / SwiftAllen-Bradley PowerFlex 520-series mounting adapter plateAllen-Bradley PowerFlex 750-seriesAllen-Bradley PowerFlex 750-series I/O shield terminationAllen-Bradley PowerFlex 755 IP00 control podAmiga 500 rear/front case screws (Retro32 replacement set)Arduino Uno / MegaASUS / MSI / Gigabyte / ASRock motherboardsBackscatter FLIP3.1 underwater filter frame screws (2x)Backscatter FLIP3.1 underwater flip-frame retaining screwBosch Rexroth swivel-in T-slot nut, slot 8
Browse all 125 in Other Equipment →The same screw also fits
Devices whose records share a thread with WREKD micro-whoop motors, closest length match first.
- Samsung Galaxy S10 / S10e / S10+ / S10 5G also M1.4 × 3.5 mm
- Rimless eyewire tension screw also M1.4 × 3.5 mm
- Eyeglass spring hinge barrel also M1.4 × 3.5 mm
- Micro RC helicopters also M1.4 × 3.5 mm
- Bredent dental prosthetic screw also M1.4 × 3.5 mm
- DIN 912 socket-head cap screw (smallest size) also M1.4 × 3.5 mm
- Binocular hinge / bridge also M1.4 × 3.5 mm
- Micro/tiny whoop drone motor mounting screws also M1.4 × 3.5 mm
Questions about WREKD micro-whoop motors screws
- What size screw does WREKD micro-whoop motors use?
- M1.4 × 3.5 mm for RENY / Phillips motor mounting screws.
- How long are the screws in WREKD micro-whoop motors?
- The record gives 3.5 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for WREKD micro-whoop motors?
- The source lists a Phillips drive. Standard M1.4 heads otherwise take PH000 / PH00 (Phillips) or T2–T3 (Torx), or a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.