Yamaha Raptor 700 ATV screw size
M6 · length not stated in the sources
Yamaha Raptor 700 ATV takes M6 metric screws. None of the sources we found gives an exact length, so measure the original before you order.
The record covers OEM fender plastic bolt/screw (Part 90149-06306).
This entry is marked confirmed and comes from insideflyer.co.uk.
For reference, M6 is 6 mm across the threads at 1 mm pitch. The imperial size people confuse it with: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6.
Yamaha Raptor 700 ATV screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M6 | not stated | 1 mm | not stated | not stated | OEM fender plastic bolt/screw (Part 90149-06306) | Confirmed |
Fitment records and sources
OEM fender plastic bolt/screw (Part 90149-06306).
pitch 1 mm · tap 5 mm · clearance 6.6 mm · PH3 / Torx T30
How to check the screw before you buy
- VESA holes are threaded inserts in the back cover; if a screw stops early, back it out rather than forcing it, because a bottomed-out screw can crack the panel housing.
- Diameter: across the threads an M6 screw measures about 6 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 1 mm from one thread crest to the next (10 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M6 heads take PH3 for Phillips and T30 for Torx, and a 5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M6 is about 7-10 N·m into metal threads and 2.5-4.0 N·m into plastic bosses; snug it up and stop.
Common mix-ups with M6
- VESA displays over 50kg move up to M8 x 1.25, which is outside metric M6 hardware - don't force an M6 bolt into a heavy-panel mount.
- VESA display mounts are M4, M6 or M8 depending on the pattern size; measure before ordering.
More in Displays, TVs & Mounts
27-34in ultrawide monitors3D printer electronics51.2V 280Ah battery pack concealed carry handleAccuracy International AICS chassis stockside securing screwsAcer / ASUS / BenQ monitorsAcer Predator X34Acer XR342CKAGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) driversAmazon Echo Dot internalsAmico patient monitor 5-inch shelf with VESA plate
Browse all 388 in Displays, TVs & Mounts →The same screw also fits
Devices whose records share a thread with Yamaha Raptor 700 ATV, closest length match first.
- Premier Mounts PBL-UMS/PBL-UMW Universal Projector Mount also M6
- Unicol VMSV2 VESA direct column fitting also M6
- VESA FDMI Part F large-format interface also M6
- LG OSW100 wall mounting bracket also M6
- ASUS VP229HF also M6
- Trimble GFX-350 / GFX-750 / XCN-750 / XCN-1050 guidance displays also M6
- Laser diode module / detector optical mount also M6
- LED video wall cabinet, frame-to-frame (SCREW A) also M6
Questions about Yamaha Raptor 700 ATV screws
- What size screw does Yamaha Raptor 700 ATV use?
- M6 for OEM fender plastic bolt/screw (Part 90149-06306).
- How long are the screws in Yamaha Raptor 700 ATV?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M6 screw?
- 1 mm (coarse), which is the standard pitch for M6 machine screws; a 0.75 mm fine pitch exists but is uncommon. The tap drill is 5 mm and the normal clearance hole is 6.6 mm.
- What screwdriver do I need for Yamaha Raptor 700 ATV?
- The sources do not name the drive. For M6, Phillips heads normally take PH3 and Torx heads T30; socket heads take a 5 mm hex key.
- Can I use an imperial screw instead of M6?
- No. Imperial look-alike: 1/4in-20 (6.35 mm) — the tripod/camera thread; visibly larger than M6. Use a true M6 screw so it does not cross-thread or strip the hole.