How long are the screws in Mindray BeneView T6/T8 Patient Monitor?

The record gives 8 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.

What is the thread pitch of an M3 screw?

0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.

What screwdriver do I need for Mindray BeneView T6/T8 Patient Monitor?

The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.

Can I use an imperial screw instead of M3?

No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Mindray BeneView T6/T8 Patient Monitor?

TechSpareWarehouse (our own store) lists M3 x 8mm, which matches the length in the records above.

Mindray BeneView T6/T8 Patient Monitor screw size

M3 · 8 mm long

The screws used on Mindray BeneView T6/T8 Patient Monitor are M3, 8 mm long.

The record covers enclosure screws for rear panel and internal board mounts.

This entry is marked confirmed and comes from manualslib.com.

For reference, M3 is 3 mm across the threads at 0.5 mm pitch. The imperial size people confuse it with: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.

Mindray BeneView T6/T8 Patient Monitor screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M3	8 mm	0.5 mm	not stated	not stated	Enclosure screws for rear panel and internal board mounts	Confirmed

Fitment records and sources

M38 mmconfirmed

Enclosure screws for rear panel and internal board mounts

pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10

Source

How to check the screw before you buy

For a wall or arm mount, the screw has to engage the threaded insert by several turns but must not bottom out, so measure the insert depth and add the thickness of the bracket and any spacers.
Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The record states 8 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
Driver: the source does not name the drive. Standard M3 heads take PH1 for Phillips and T10 for Torx, and a 2.5 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M3

Telescope thumbscrews are sold in a wide non-metric legacy range too (1/4-20, 8-32, 10-32 on many Meade/Celestron mounts), so metric M3/M4 fitment applies mainly to newer/international accessory ecosystems (SkyWatcher, generic 1.25" accessories) and should not be assumed universal.
GE patient monitors often use 'PT 3x10mm' screws; these are thread-forming screws for plastic and are NOT standard M3 machine threads.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Displays, TVs & Mounts

27-34in ultrawide monitors 3D printer electronics 51.2V 280Ah battery pack concealed carry handle Accuracy International AICS chassis stockside securing screws Acer / ASUS / BenQ monitors Acer Predator X34 Acer XR342CK AGCO SimplEbale monitor kit (Massey Ferguson MF 1800)Alpha Series performance display (forklift)Amazon Echo (full size) drivers Amazon Echo Dot internals Amico patient monitor 5-inch shelf with VESA plate

Browse all 388 in Displays, TVs & Mounts →

The same screw also fits

Devices whose records share a thread with Mindray BeneView T6/T8 Patient Monitor, closest length match first.

Apple HomePod internal drivers also M3 × 8 mm
Philips IntelliVue MP40/MP50 Patient Monitors also M3 × 8 mm
Soundbar drivers and boards also M3 × 8 mm
Dell U2721DE also M3 × 8 mm
Dell U2719D also M3 × 8 mm
Dell S2425H monitor also M3 × 8 mm
Zebra / Motorola barcode scanner bracket (Havis FlexiPole) also M3 × 8 mm
Dell U2419H also M3 × 8 mm

Questions about Mindray BeneView T6/T8 Patient Monitor screws

What size screw does Mindray BeneView T6/T8 Patient Monitor use?: M3 × 8 mm for enclosure screws for rear panel and internal board mounts.
How long are the screws in Mindray BeneView T6/T8 Patient Monitor?: The record gives 8 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
What is the thread pitch of an M3 screw?: 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
What screwdriver do I need for Mindray BeneView T6/T8 Patient Monitor?: The sources do not name the drive. For M3, Phillips heads normally take PH1 and Torx heads T10; socket heads take a 2.5 mm hex key.
Can I use an imperial screw instead of M3?: No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for Mindray BeneView T6/T8 Patient Monitor?: TechSpareWarehouse (our own store) lists M3 x 8mm, which matches the length in the records above.

Heads up: shipping delay