How long are the screws in Sony PlayStation 5 vertical stand?

The records range from 8 to 12 mm depending on the position, so match each screw to its own hole.

What is the thread pitch of an M3 screw?

0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.

What screwdriver do I need for Sony PlayStation 5 vertical stand?

The source lists a Phillips drive. Standard M3 heads otherwise take PH1 (Phillips) or T10 (Torx), or a 2.5 mm hex key.

Can I use an imperial screw instead of M3?

No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.

Where can I buy replacement screws for Sony PlayStation 5 vertical stand?

TechSpareWarehouse (our own store) lists M3 x 8mm, M3 x 10mm and M3 x 12mm, which match lengths in the records above.

Sony PlayStation 5 vertical stand screw size

M3 · 8 to 12 mm long

Sony PlayStation 5 vertical stand takes M3 metric screws in lengths from 8 to 12 mm.

The record covers single Phillips stand screw; length reported as 8mm or 12mm depending on source.

Head and drive, as the source states them: Phillips drive.

This entry is marked likely and comes from electronics.alibaba.com.

For reference, M3 is 3 mm across the threads at 0.5 mm pitch. The imperial size people confuse it with: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3.

Sony PlayStation 5 vertical stand screw specifications

One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.

Thread	Length	Pitch	Head	Drive	Where it goes	Status
M3	8–12 mm	0.5 mm	not stated	Phillips	Single Phillips stand screw; length reported as 8mm or 12mm depending on source	Likely

Fitment records and sources

M38-12mmlikely

Single Phillips stand screw; length reported as 8mm or 12mm depending on source

pitch 0.5 mm · tap 2.5 mm · clearance 3.4 mm · PH1 / Torx T10

Source

How to check the screw before you buy

Keep long and short screws apart when opening a console; the shell positions differ.
Diameter: across the threads an M3 screw measures about 3 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
Pitch: 0.5 mm from one thread crest to the next (20 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
The records span 8–12 mm, which means different positions take different lengths — match each hole to its own screw.
Driver: the source names a Phillips drive. For comparison, standard M3 heads take PH1 (Phillips) or T10 (Torx), or a 2.5 mm hex key.
Tightening: no device-specific torque is published in these records. The site's general figure for M3 is about 80-130 N·cm into metal threads and 35-60 N·cm into plastic bosses; snug it up and stop.

Common mix-ups with M3

Eurorack rail thread varies by manufacturer: some tapped M2.5, some M3 — not a single universal standard.
M3 (3.0mm, 0.5mm pitch) is not #6-32 UNC (~3.5mm) — they look identical and cross-thread, the single most common PC-building mistake.

Pitch gauge · Screw size finder · Torque guide

Buy these screws at TechSpare Warehouse

In stock and shipped from South Carolina. Our black screws are Phillips wafer head (low profile); match the head style and length to the original before you order.

More in Gaming & Peripherals

Arcade cabinet control panel Dell Latitude 3190 / 3190 2-in-1 Dell Latitude 3490 Dell XPS 13 9315 Diebold Nixdorf ATM ESC (Encrypting PIN Pad/keyboard) cross screw Docking station internal boards Feurich Olya EVO digital piano/E-Piano Generic tray-mount mechanical keyboards HTC Vive controller Inkjet printer / scanner frames KBDfans countersunk standoff kit Keychron K3 / K3 Pro / K3 Max

Browse all 30 in Gaming & Peripherals →

The same screw also fits

Devices whose records share a thread with Sony PlayStation 5 vertical stand, closest length match first.

Pinscape DIY pinball cabinet also M3 × 8–12 mm
Sanwa JLF joystick mounting plate (arcade control panel) also M3 × 8 mm
Arcade cabinet control panel also M3 × 8–12 mm
Inkjet printer / scanner frames also M3 × 10–12 mm
USB-C docking station chassis also M3 × 8–10 mm
Bambu Lab AMS unit also M3 × 8–12 mm
Airsoft red dot sight mounting screw set (Laylax/Quintes Sence) also M3 × 8–10 mm
Apple HomePod internal drivers also M3 × 8–10 mm

Questions about Sony PlayStation 5 vertical stand screws

What size screw does Sony PlayStation 5 vertical stand use?: M3 × 8–12 mm for single Phillips stand screw; length reported as 8mm or 12mm depending on source.
How long are the screws in Sony PlayStation 5 vertical stand?: The records range from 8 to 12 mm depending on the position, so match each screw to its own hole.
What is the thread pitch of an M3 screw?: 0.5 mm (coarse), which is the standard pitch for M3 machine screws; a 0.35 mm fine pitch exists but is uncommon. The tap drill is 2.5 mm and the normal clearance hole is 3.4 mm.
What screwdriver do I need for Sony PlayStation 5 vertical stand?: The source lists a Phillips drive. Standard M3 heads otherwise take PH1 (Phillips) or T10 (Torx), or a 2.5 mm hex key.
Can I use an imperial screw instead of M3?: No. Imperial look-alike: #5-40 (3.18 mm) or #4-40 — neither interchanges with M3. Use a true M3 screw so it does not cross-thread or strip the hole.
Where can I buy replacement screws for Sony PlayStation 5 vertical stand?: TechSpareWarehouse (our own store) lists M3 x 8mm, M3 x 10mm and M3 x 12mm, which match lengths in the records above.

Heads up: shipping delay