NBK SSCZS miniature captive screw for precision instrument panels screw size
M1.4 · length not stated in the sources
NBK SSCZS miniature captive screw for precision instrument panels takes M1.4 metric screws. None of the sources we found gives an exact length, so measure the original before you order.
Where it is used: NBK SSCZS-M1.4 miniature captive panel screw.
This entry is marked confirmed and comes from govolition.com.
An M1.4 screw is 1.4 mm in diameter with a 0.3 mm pitch, tapped with a 1.1 mm drill; imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
NBK SSCZS miniature captive screw for precision instrument panels screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | not stated | 0.3 mm | not stated | not stated | NBK SSCZS-M1.4 miniature captive panel screwcaptive | Confirmed |
Fitment records and sources
NBK SSCZS-M1.4 miniature captive panel screw
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- Stage and rack gear mixes metric with #10-32 rack screws, so check before swapping.
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: measure from under the head to the tip for pan, button, wafer and cap heads; countersunk (flat) heads are measured overall.
- Driver: the source does not name the drive. Standard M1.4 heads take PH000 / PH00 for Phillips and T2–T3 for Torx, and a 1.3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- M1.4 is THE Samsung Galaxy internal screw across S, A, M and Note lines — but lengths run 2.3mm to 4mm+ and are not interchangeable between models.
More in Audio, Music & Stage
The same screw also fits
Devices whose records share a thread with NBK SSCZS miniature captive screw for precision instrument panels, closest length match first.
- NBK SSCZS-M1.4 captive screw also M1.4
- Precision instrument panels also M1.4
- NBK SSCZS miniature captive screw for precision instruments also M1.4
- Dell Precision 5470 also M1.4
- Hearing aid shells also M1.4
- Tiny Whoop / micro FPV drone flight controller & ESC mounting screws also M1.4
- Samsung Galaxy S23 board screws also M1.4
- Oakley O Matter / steel frame hinge also M1.4
Questions about NBK SSCZS miniature captive screw for precision instrument panels screws
- What size screw does NBK SSCZS miniature captive screw for precision instrument panels use?
- M1.4 for NBK SSCZS-M1.4 miniature captive panel screw.
- How long are the screws in NBK SSCZS miniature captive screw for precision instrument panels?
- None of the sources states a length. Remove one screw and measure it from under the head to the tip (overall for a countersunk head).
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for NBK SSCZS miniature captive screw for precision instrument panels?
- The sources do not name the drive. For M1.4, Phillips heads normally take PH000 / PH00 and Torx heads T2–T3; socket heads take a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.