Precision instrument panels screw size
M1.4 · 1.1 mm long
Precision instrument panels takes M1.4 metric screws, 1.1 mm long.
It is listed for NBK/SAIDA pan-head captive screws.
Head and drive, as the source states them: pan head.
This entry is marked confirmed and comes from del-screw.com.
An M1.4 screw is 1.4 mm in diameter with a 0.3 mm pitch, tapped with a 1.1 mm drill; imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix.
Precision instrument panels screw specifications
One row per fitment record. Head, drive are shown only where the source states them; pitch is the ISO coarse pitch for the thread.
| Thread | Length | Pitch | Head | Drive | Where it goes | Status |
|---|---|---|---|---|---|---|
| M1.4 | 1.1 mm | 0.3 mm | Pan head | not stated | NBK/SAIDA pan-head captive screwscaptive | Confirmed |
Fitment records and sources
NBK/SAIDA pan-head captive screws
pitch 0.3 mm · tap 1.1 mm · clearance 1.6 mm · PH000 / PH00 / Torx T2–T3
How to check the screw before you buy
- Stage and rack gear mixes metric with #10-32 rack screws, so check before swapping.
- Diameter: across the threads an M1.4 screw measures about 1.4 mm with calipers (usually a hair under). If yours measures noticeably more or less, it is a different thread.
- Pitch: 0.3 mm from one thread crest to the next (33.33 crests per centimetre). A thread pitch gauge or the pitch-gauge tool settles it in seconds.
- Length: for pan head screws, measure from under the head to the tip (countersunk heads are the exception: they are measured overall).
- The record states 1.1 mm. Going longer risks bottoming out or touching parts behind the hole; going shorter loses thread engagement.
- Driver: the source does not name the drive. Standard M1.4 heads take PH000 / PH00 for Phillips and T2–T3 for Torx, and a 1.3 mm hex key for socket heads; a bit that fits loosely will cam out and strip the head.
- Tightening: no device-specific torque is published in these records. The site's general figure for M1.4 is about 8-12 N·cm into metal threads and 4-7 N·cm into plastic bosses; snug it up and stop.
Common mix-ups with M1.4
- M1.4 is THE Samsung Galaxy internal screw across S, A, M and Note lines — but lengths run 2.3mm to 4mm+ and are not interchangeable between models.
More in Audio, Music & Stage
Accordion reed blocksAllparts metric bridge length screwsARRI Mini Follow Focus MFF-2 / related follow-focus hardwareBoss compact guitar pedal battery doorCymbal stand / hi-hat wing nutCymbal stand top wing nutCymbal stand wing nutDrum hardware wing bolt / memory lockDrum tension rodDrum tension rod / lug mounting screwDuratruss Mini 360 F14 10kg truss clampFender Standard Series bass bridge
Browse all 48 in Audio, Music & Stage →The same screw also fits
Devices whose records share a thread with Precision instrument panels, closest length match first.
- NBK SSCZS miniature captive screw for precision instruments also M1.4
- NBK SSCZS-M1.4 captive screw also M1.4
- NBK SSCZS miniature captive screw for precision instrument panels also M1.4
- Zeiss camera lens focus scale screw also M1.4
- Fairphone 2 internal screws also M1.4
- NeoBiotech fixture remover screw also M1.4
- Fairphone 3 / Fairphone 4 also M1.4
- Eyeglass hinge screw (internal thread spec) also M1.4
Questions about Precision instrument panels screws
- What size screw does Precision instrument panels use?
- M1.4 × 1.1 mm for NBK/SAIDA pan-head captive screws.
- How long are the screws in Precision instrument panels?
- The record gives 1.1 mm. Measure the original from under the head (overall for a countersunk head) to confirm before ordering.
- What is the thread pitch of an M1.4 screw?
- 0.3 mm (coarse), which is the standard pitch for M1.4 machine screws. The tap drill is 1.1 mm and the normal clearance hole is 1.6 mm.
- What screwdriver do I need for Precision instrument panels?
- The sources do not name the drive. For M1.4, Phillips heads normally take PH000 / PH00 and Torx heads T2–T3; socket heads take a 1.3 mm hex key.
- Can I use an imperial screw instead of M1.4?
- No. Imperial look-alike: #0-80 UNF (1.52 mm) — close in diameter, different pitch, do not mix. Use a true M1.4 screw so it does not cross-thread or strip the hole.